Feynlab The Original Ceramic Coating

FEYNLAB® THE ORIGINAL CERAMIC COATING

A simple to apply, durable, cost-effective, and glossy ceramic coating – greatly outperforming waxes or sealants. The original ceramic coating (formerly ceramic lite).

• The most economical and simple to apply ceramic nano coating in the FEYNLAB® family.
  
• Simple installation, with a friendly wipe on / wipe off application.
• A hydrophobic surface, easily out performing all traditional waxes and sealants.
• Surface versatility – May be used to protect most vehicle exterior surfaces. 
• Provides a coated vehicle with an impressive combination of ultra-slickness, durability, gloss, and hydrophobic properties.
• FEYNLAB’s® true nano technology and bonding chemistry allows for an unparalleled level of protection since the formula penetrates further into the existing paint structure than anything else available.

Durability & Approved Surfaces

Durability: 1+ Year(s)

APPROVED SURFACES FOR APPLICATION ONLY: – DO NOT apply to unapproved surfaces

• Clear-coated painted surfaces (see warranty terms & conditions for approved manufacturers & vehicle types
• Black textured plastics (test if unsure)
• Headlights & Tail-lights
• Black piano trim
• Clear-coated painted wheel rims & calipers

Shelf Life
Unopened  – 1 year.  Opened – Use within 1-2 months. ALWAYS keep cap on bottle when not in use.

Included
40ml FEYNLAB® THE ORIGINAL CERAMIC (enough for 1 mid-sized vehicle)

Cautions
Always wear respirator & gloves during application. Ensure application area is free of loose contamination.

Paint Preparation
Thoroughly clean vehicle surface using FEYNLAB® PURE WASH. Follow with a topical decontamination clay treatment using FEYNLAB® PRIME. If necessary, use a ferrous iron removal product to remove all embedded iron deposits.

After polishing paint to the desired level, remove all polish oils using FEYNLAB® PANEL PREP to ensure optimal bonding and durability of the coating. After completing Panel Prep on all surfaces, wait a minimum of 10 min after using panel prep before coating application.

Directions
Prior to application, place vehicle in a well lit, temperature controlled 10°C-30°C (50°F-85°F), & contamination free environment. Have plenty (6 or more) new microfiber towels, 2 or 3 microfiber applicators on hand BEFORE application.

Once the vehicle is prepared, it is strongly recommended to tape off and protect all unapproved surfaces. This minimizes the risk of etching by the solvents in FEYNLAB® CERAMIC on unapproved surfaces. Avoid these surfaces with CERAMIC and wipe off immediately if any product accidentally finds these surfaces.

Shake CERAMIC vigorously for 2 min before use. Open the bottle and allow the coating 1 min of air exposure.

CERAMIC Application Instructions

1. Apply enough CERAMIC to a microfiber applicator to fully cover a single panel such as a door or half a hood.
2. Make a “+” (plus) sign with product in the middle of the panel, then wipe around the boundaries of the section creating a frame.
3. Next, fill in the framed area with slightly overlapping horizontal (left to right) straight lines over the entire panel. After, switch to vertical overlapping lines. This cross-hatching pattern ensures even application.
4. Due to its user friendliness, CERAMIC may be applied to the entire vehicle before removal.
5. After application, step back and look for any areas missed or those with excess product. If found, smooth out evenly with the applicator sponge. This will ensure even drying across the panel and minimize excess product usage.
6. Allow CERAMIC to dwell on the panel a minimum of 15-20 min, until it is about 75% dry. Dwell time may vary depending on humidity and temperature. * Humid Climates 75%+ = Shorter Dwell time.
7. To test removal readiness: lightly swipe a small spot with a gloved finger. If the swipe reveals a clean trail then remove. If the swipe smears then allow it to dwell longer. Repeat swipe test again in 2-5 min increments to determine wipe times.
8. Wipe off CERAMIC following same pattern of application, using two clean MF towels. Towel A (left hand) will remove (level) the majority of the coating. Towel B (right hand) will remove any remaining residue, revealing a crystal clear surface.

Recommended Maximum Area of Application:
ENTIRE vehicle, then wipe off in same pattern as application.

Note: If using CERAMIC on black textured plastics, perform a simple wipe after 1-2 min to ensure even application and wipe clear if you see any residue or uneven areas.

Final Inspection
Be sure to carefully inspect all finished panels for any leftover coating residue (high spots) during the final wipe. Commonly edges, emblems, and other tight areas may contain some remaining residue. High spots are much easier to remove if caught within a 20-40 min window after the final wipe, than later when the coating has setup.

Layering
Although one layer of CERAMIC is sufficient to achieve the one-year durability on clear-coated painted surfaces, another coat may be applied to any area to gain additional thickness (such as the hood or front bumper).

To layer CERAMIC, wait 1-3 hours before applying a second layer. DO NOT wait longer than 3 hours after first layer or cloudiness will result.

Infrared Curing (Optional)
Bake each panel with an IR lamp to reach a surface temperature of 60°C (140°F) for 15min at a distance of ~ 30-36″ from the panel.

Post Application Instructions

• Avoid any incidental water exposure for 24 hours. If it occurs, gently wipe water off the surface.
• Avoid all chemicals including car washes for 7 days.
• If the vehicle must be released in wet conditions before 24hrs after the final coating, then apply FEYNLAB®  DETAILER after 1-2 hours of curing time.
• Wash & Maintain Paint Regularly using FEYNLAB® PURE WASH or FEYNLAB® PURE RINSELESS.

Climate Notes
All FEYNLAB® Coatings are subject to different dwell and curing time windows due to humidity and temperature conditions. In General, the higher the humidity level the quicker the coating will cure. If humidity level approaches 75% or higher then consider lessening the recommended dwell and wipe times for the coating. 

Additionally moving air will decrease coating dwell times for areas it contacts. Therefore, it is recommended to stop all moving air as much as possible during coating applications to ensure consistency for all portions of the vehicle.

Coatings are best applied in temperature controlled environments of  10°C-30°C (50°F-85°F), with humidity as low as possible.